This folding cargo carrier form Uriah Products is a practical device that will give you room to carry up to 500 pounds of cargo on the rear of your vehicle. It mounts right to your vehicle’s hitch and works with most 2” receivers. It measures 60” x 22” and you can easily fold it up when not in use to take up less space and drive a little safer. It has holes for tie-down straps all over and it has a mesh bottom that allows moisture to easily drain.
This Uriah Products tandem-axle trailer fender has a teardrop design and no back. It’s constructed out of durable 16-gauge cold rolled steel, and it’s unfinished so that you can weld it and paint it just how you like. Its 9” by 72” dimensions make it ready to accept up to 16” tires.
This 2-pack of Uriah Products bearing protectors will help keep your trailer’s wheel bearing assemblies clean and running smoothly. They have an outer diameter of 1.986” and will fit any hub that requires that size cap. They have a grease fitting that allows you to lubricate the spindles without removing the caps while protecting the spindle bearings from seizing from contamination. These caps are especially useful on boat trailers that are occasionally submerged in water.
The adjustable tri-ball mount from Uriah Products allows you to quickly change between different ball sizes without needing to remove the assembly or carry multiple mounts. It’s perfect for vehicles that regularly tow different trailers. It includes three ball hitches: 1-7/8”, 2”, and 2-5/16”, and a 2-point mounting design that provides stability and safety. It fits standard 2” square receiving tubes and has a 10,000 lb maximum GTW rating along with a 1000 lb maximum tongue rating. This model is adjustable, too, so you can easily tow trailers of different heights.
With this chrome tri-ball mount from Uriah Products you can hitch three trailers with different hitches without needing to carry around extra ball mounts or perform time consuming hitch switches. This mount includes 1-7/8”, 2”, and 2-15/16” ball hitches that are plated in chrome for superb durability. They’re securely welded to a solid shank, and all you have to do to adjust them is remove the hitch pin, pull the shank out of the receiver, rotate to your preferred size, and you’re ready to put the shank back into the receiver, reinsert the pin, and be on your way!
This red LED stop/turn/tail/back-up light from Uriah Products comes ready for installation with a rubber grommet and a standard three-prong plug design. It’s sealed to keep out water, making it acceptable for use on boat trailers, and the contact sockets are filled with silicone to prevent corrosion. It fits standard trailer light mounts, and the LED has seven diodes to throw off more than enough light.
These nylon spring bushings from Uriah Products fit 1-3/4” leaf springs. They come in packs of six, and they have a 9/16” inner diameter, an 11/16” outer diameter, and are 1-3/4” long.
This magnetic towing light kit from Uriah Products installs quickly and allows your trailer to meet DOT specifications. This kit comes with two stop/turn/tail lights that are attached strong, scratch-resistant magnets for safe attachment, a 4-way flat harness adapter, 20’ of wire, and a 5’ span between the lights, allowing them to fit almost any vehicle. The lights have red rear-facing lenses and amber front-facing lenses.
This Uriah Products bearing spindle is a BT16 replacement spindle for 1-1/16” inner and outer bearings. It’s machined out of steel for solid durability, and it’s designed to be welded onto your axle.
This single-axle fender comes from Uriah Products manufactured out of 16-gauge cold rolled steel with a 1” lip on the sides. It has an unfinished design that means you’re free to weld and paint it how you like, and its 9” by 32” size allows it to accommodate up to 15” tires.
Uriah's Class II Coupler Repair Kit is a great backup to have on hand for your trailer. The coupler is zinc plated to reduce corrosion. This kit includes latch, spring, nut, and ball lock, and is universal for all straight tongue and A-Frame couplers.
By keeping some of these Uriah Products replacement U-bolts on hand, you’ll be able to replace existing worn U-bolts on your trailers before they break, saving you the headache of having one break on you when you’re on the road. These U-bolts come in a back of two and included the required nuts. They’re 5-1/2” long and accommodate 2-3/8” axles.
This submersible lighting kit from Uriah Products contains everything you need to quickly install a rear lighting system that meets DOT standards trailers that are under 80” wide. The lights are sealed to be waterproof and fully submersible, making them a great fit for boat trailers, but they can be used on other trailers, too. The kit includes two bright LED stop/turn/tail lights that mount with strong, scratch-resistant magnets, a flat 4-way harness adapter, a license bracket, and 20’ of wire.
Since trailer axle U-bolts are some of the trailer components that experience the most wear and break most frequently, it’s a good idea to keep some extras, like these Uriah Products square U-bolts, on hand. That way you can monitor your existing U-bolts and replace them at the first sign of wear, allowing you to avoid a dangerous, time-consuming breakdown on the road. These U-bolts are 5-1/4” long and accommodate 2” axles, and they come with the necessary nuts for installation.
This Uriah Products red LED stop/turn/tail/back-up light with flange is designed to be mounted onto a flat surface for installation, or it can fit into standard trailer light mounts. It uses standard three-prong plugs, and it’s sealed to be watertight, making it an acceptable option for use on a boat trailer. The contact sockets are filled with silicone for corrosion resistance and added durability.
This round reflector from Uriah Products has an adhesive back for easy installation. It’s 3-3/16” in diameter, and it is designed to help your trailer meet DOT requirements for reflectivity, though it’s useful in just about any other application that calls for a reflector. The adhesive backing is designed to stick securely to metal, painted metal, and plastic.
This Uriah Products kit contains the screws and sleeves to anchor your wheel chocks to a wood floor, giving you a little bit of added safety.
This set of EZ lube style drive-in grease caps from Uriah Products will help keep your wheel bearing assembly running smoother by protecting it from dirt and debris. The EZ lube style makes lubrication easier by allowing you to just remove the plug rather than the caps. These caps have a diameter of 1.986”.
Uriah Products offers this 14-gauge 7-wire trailer cable that should last you through a number of projects. The color-coded wires are coated in durable, weatherproof PVC to last for years to come. While this cable was designed for use as trailer wiring, you can also use it in any project that calls for 6 conductor, low-voltage cable in 14 AWG.This product is sold by the foot so you can purchase just the right amount!
This heat-shrinking tube assortment from Uriah Products includes five pieces of red, blue, and yellow insulated pieces of varying sizes (1/8”, 3/16”, and 1/4”). They all heat shrink when heat is applied and create durable, waterproof seals.This product is available in assorted colors. Please contact your nearest Murdoch's store for available color choices.
This 4-bolt hub kit from Uriah Products is a complete replacement assembly for an axle hub on boat trailers or similar utility trailers. It’s a BT8 type, and it comes with a 4” bolt circle, 4 bolts, and 1” inner and outer bearings. It’s designed for axles with a capacity of 1,250 pounds.
This weld-on hanger kit from Uriah Products will help you install single axle, double-eye, and 1-3/4” springs. It includes everything you need to hang two springs, including two brackets, shackles, and shackle straps.
This two-pole flat trailer wire connector from Uriah Products is a durable, 12” flat extension loop. You can use it with 12-volt accessories, and if you want you can cut the cord to create two compatible plugs. It features 16-gauge copper wire construction and tin-plated corrosion-resistant corrosion.